50 Caliber Racing ON/OFF Waterproof Rocker Switch, LED Backlit with Custom Etched Sexy Girl Design

"Head Lights"

High quality single pole, single throw ON/OFF rocker switch, a 20 amp switch for 12 or 24 volt system. LED Backlit Illumination with a custom etched design, guaranteed to put smile on your face.

Be sure to choose color before ordering!

50 Caliber Racing CDI module for 660 Yamaha Rhino and Grizzly

Our performance CDI module will give you the most bang for your buck. With increased spark energy you will experience easier starting and better throttle response. Removes the speed limiter and increases max revs by 1000 to 7800 RPM. It also will eliminate the reverse rev limiter. Compatible with both standard gauges and Rhino digital dash. Also compatible with factory exhaust and factory intake. Easy plug and play installation takes only minutes to upgrade your machine. 

50 Caliber Racing Steel Weld In Bung.

Heavy duty weld in bung. Used for fabricating custom tie rods, control arms, sway bar links and more. Center hole is threaded all the way through for maximum strength. Available in right or left hand thread. 

Be sure to select the quantity before ordering!

Tie Rod End Kit for Honda FL250 Odyssey ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. This kit will service one side. Includes 1 inner and 1 outer end for the tie rod on your Honda.

On/Off/On Rocker Switch-  50 Caliber Racing On/Off Rocker Switch - This rocker switch is a 20 amp switch and can be used for 12 or 24 Volt applications.  These are completely waterproof and can be used in UTV's, Boats, Cars, Trucks, Sand Rails, as well as any other vehicle.

50 Caliber Racing Steel Weld In Bung.

Heavy duty weld in bung. Used for fabricating custom tie rods, control arms, sway bar links and more. Center hole is threaded all the way through for maximum strength. Available in right or left hand thread. 

Be sure to select the quantity before ordering!

Tie Rod End Kit for Kawasaki KFV 750 Brute Force ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Elite Series 5.5 inch LED Bar with Flood Beam

- Dimensions: 6.75"(L) x 2.7’’(H ) x 3’’(D)
- Operates on 9-36 Volts DC including 12 and 24 Volts
- Flood beam - 12 LED bulbs 3 watt each 36 watts total
- Pivoting mounting system
- 3600 lumens, 6000k
- FREE 50 Caliber Koozie with Each light bar order!

Heavy Duty 4130 Chromoly Heim Joints with Nylon / PTFE Liner - Male Right Hand Thread in 1/2" up to 7/8"

Heavy duty male threaded heim joint rod ends with nylon / PTFE liner. Made from 4130 Chromoly alloy and rated at nearly 18,000 pounds. The load rating and size make these excellent for building custom tie rods and radius arms for UTVs. Includes jam nut. Available in RH or LH thread.

Attn Dealers: Quantity discounts apply to this product in the shopping cart at 2+ and 10+ qty. 

50" Curved Light Bar Mounting Brackets for 14-15 Chevy and GMC Trucks

- Strong, sleek, Aerodynamic design
- Mild Steel Construction
- Upper windshield mount
- Includes installation hardware
- Quick easy install
- Designed to fit 50 Caliber Racing 50” Curved LED Light Bar (5045-A12)

Vintage Stage 1 88cc Big Bore kit (52mm bore)

- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation
- High compression 52mm piston with rings, pin, & clips (can still run pump gas)
- Head gasket kit includes all gasket needed to install bore kit.

Heavy Duty 4130 Chromoly Heim Joints with Nylon / PTFE Liner - Male Left Hand Thread in 1/2" up to 7/8"

Heavy duty male threaded heim joint rod ends with nylon / PTFE liner. Made from 4130 Chromoly alloy and rated at nearly 18,000 pounds. The load rating and size make these excellent for building custom tie rods and radius arms for UTVs. Includes jam nut. Available in RH or LH thread.

Attn Dealers: Quantity discounts apply to this product in the shopping cart at 2+ and 10+ qty. 

50" Curved Light Bar Mounting Brackets for 10-14 Ford F-150 SVT Raptor

- Strong, sleek, aerodynamic design
- Mild Steel Construction
- Includes installation hardware
- Quick easy install
- Designed to fit 50 Caliber Racing 50” Curved LED Light Bar [5045-A12] (not included)

Vintage Stage 2 88cc Big Bore kit

- Fits 1968-1981 honda z50, ct70, atc70, trx70, sl70, xl70
- 20mm Carburetor
- 52mm Piston and cylinder
- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation

High Angle Misalignment Spacers for Heim Joints made from zinc plated 4130 chromoly steel. Available in several sizes to fit any fabrication project. Price is for one pair of spacers, enough for one heim joint.

Be sure to choose the correct size and quantity before ordering!

50" Straight Light Bar Mounting Brackets for 10-14 Ford F-150 SVT Raptor

- Strong, sleek, aerodynamic design
- Mild Steel Construction
- Brow mount
- Includes installation hardware
- Quick easy install
- Designed to fit 50 Caliber Racing 50” Straight LED Light Bar [5040] (not included)

50 Caliber Racing Race Head, 88cc Big Bore kit, and 20mm Carburetor

Our Race Head has been updated for even more performance! It now has 25/22mm valves with better porting/flow. We also kept the combustion chamber the same size and changed the angle of the valves slightly. This will really wake up your stock engine and is comparable in power to the much larger Chinese 124cc engines!

Single rod end kit including a 5/8 x 5/8 chromoly heim joint with nylon/teflon liner, jam nut, and chromoly steel weld in bung tube adapter. Designed specifically for 1.25" OD tubing, with wall thickness of .095 or .120. Excellent for building custom sway bar links, tie rods and radius arms for UTVs, and more. Available with or without high misalignment spacers.

Be sure to choose tubing wall thickness, thread direction and misalignment spacer options before ordering!

50" Curved Light Bar Mounting Brackets for 09-14 Ford F-150

- Strong, sleek, aerodynamic design
- Mild Steel Construction
- Roof mount
- Includes installation hardware
- Quick easy install
- Designed to fit 50 Caliber Racing 50” Curved LED Light Bar [5045-A12] (not included)

Rod end fabrication kit with 5/8 x 5/8 chromoly heim joint with nylon/teflon liner, jam nut, and chromoly steel weld in bung tube adapter. Designed specifically for 1.25" OD tubing, with wall thickness of .095 or .120. Excellent for building a custom panhard bar for UTVs, cars, trucks & more. Includes LH and RH heim joint, with matching bungs. Available with or without high misalignment spacers.

Be sure to choose tubing wall thickness and misalignment spacer options before ordering!