50 Caliber Racing Steel Weld In Bung for 1" ID Round Tube - 5/8-18 Threaded Through

Heavy duty weld in bung with 5/8-18 threaded center hole. Used for fabricating custom tie rods, control arms, sway bar links and more. Center hole is threaded all the way through for maximum strength. Designed to slip fit into 1.25" OD .120 wall round tubing with an ID of 1". Available in right or left hand thread. 

Be sure to select thread direction and quantity before ordering!

50 Caliber Racing CDI module for 660 Yamaha Rhino and Grizzly

Our performance CDI module will give you the most bang for your buck. With increased spark energy you will experience easier starting and better throttle response. Removes the speed limiter and increases max revs by 1000 to 7800 RPM. It also will eliminate the reverse rev limiter. Compatible with both standard gauges and Rhino digital dash. Also compatible with factory exhaust and factory intake. Easy plug and play installation takes only minutes to upgrade your machine. 

50 Caliber Racing's Elite Series 4 Point Harness with Ultra Kush Padding for maximum comfort

- Available in 2" and 3" wide straps- Sewn in pads for maximum comfort
- Automotive style buckle with push button release
- Black anodized hardware
- Adjustable straps to fit almost anyone
- Available in 4 point only
- Many designs and colors available: Sugar skulls red and black, Bandana red, black, blue 

Available as Racing harness only or with a bypass plug (sold separately) for Polaris RZR or Can-Am UTVs.

50 Caliber Racing Steel Weld In Bung.

Heavy duty weld in bung. Used for fabricating custom tie rods, control arms, sway bar links and more. Center hole is threaded all the way through for maximum strength. Available in right or left hand thread. 

Be sure to select the quantity before ordering!

Tie Rod End Kit for Honda FL250 Odyssey ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. This kit will service one side. Includes 1 inner and 1 outer end for the tie rod on your Honda.

50 Caliber Racing 4 Point Harness with black hardware and push button release

- Available in 2" and 3" wide straps
- Sewn in pads for maximum comfort
- Automotive style buckle with push button release
- Black anodized hardware
- Adjustable straps to fit almost anyone
- Available in 4 point only
- Many colors available: Black, Red, Blue, Silver, Orange, Pink, Green, Purple, Yellow, and Camo

Available as Racing harness only or with a bypass plug (sold separately) for Polaris RZR or Can-Am UTVs.

50 Caliber Racing Steel Weld In Bung.

Heavy duty weld in bung. Used for fabricating custom tie rods, control arms, sway bar links and more. Center hole is threaded all the way through for maximum strength. Available in right or left hand thread. 

Be sure to select the quantity before ordering!

Tie Rod End Kit for Kawasaki KFV 750 Brute Force ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Heavy Duty 4130 Chromoly Heim Joints with Nylon / PTFE Liner - Male Right Hand Thread in 1/2" up to 7/8"

Heavy duty male threaded heim joint rod ends with nylon / PTFE liner. Made from 4130 Chromoly alloy and rated at nearly 18,000 pounds. The load rating and size make these excellent for building custom tie rods and radius arms for UTVs. Includes jam nut. Available in RH or LH thread.

Attn Dealers: Quantity discounts apply to this product in the shopping cart at 2+ and 10+ qty. 

Vintage Stage 1 88cc Big Bore kit (52mm bore)

- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation
- High compression 52mm piston with rings, pin, & clips (can still run pump gas)
- Head gasket kit includes all gasket needed to install bore kit.

Heavy Duty 4130 Chromoly Heim Joints with Nylon / PTFE Liner - Male Left Hand Thread in 1/2" up to 7/8"

Heavy duty male threaded heim joint rod ends with nylon / PTFE liner. Made from 4130 Chromoly alloy and rated at nearly 18,000 pounds. The load rating and size make these excellent for building custom tie rods and radius arms for UTVs. Includes jam nut. Available in RH or LH thread.

Attn Dealers: Quantity discounts apply to this product in the shopping cart at 2+ and 10+ qty. 

Vintage Stage 2 88cc Big Bore kit

- Fits 1968-1981 honda z50, ct70, atc70, trx70, sl70, xl70
- 20mm Carburetor
- 52mm Piston and cylinder
- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation

High Angle Misalignment Spacers for Heim Joints made from zinc plated 4130 chromoly steel. Available in several sizes to fit any fabrication project. Price is for one pair of spacers, enough for one heim joint.

Be sure to choose the correct size and quantity before ordering!

50 Caliber Racing Race Head, 88cc Big Bore kit, and 20mm Carburetor

Our Race Head has been updated for even more performance! It now has 25/22mm valves with better porting/flow. We also kept the combustion chamber the same size and changed the angle of the valves slightly. This will really wake up your stock engine and is comparable in power to the much larger Chinese 124cc engines!

Single rod end kit including a 5/8 x 5/8 chromoly heim joint with nylon/teflon liner, jam nut, and chromoly steel weld in bung tube adapter. Designed specifically for 1.25" OD tubing, with wall thickness of .095 or .120. Excellent for building custom sway bar links, tie rods and radius arms for UTVs, and more. Available with or without high misalignment spacers.

Be sure to choose tubing wall thickness, thread direction and misalignment spacer options before ordering!

Polaris 600 700 800 Sportsman Ranger RZR Cooling Fan 2002-2015

Brand new cooling fan assembly including clips. Manufactured to OEM spec for an exact fit, just remove, replace and ride!

For Polaris Sportsman 600-800 , Ranger 800, and RZR 800

Rod end fabrication kit with 5/8 x 5/8 chromoly heim joint with nylon/teflon liner, jam nut, and chromoly steel weld in bung tube adapter. Designed specifically for 1.25" OD tubing, with wall thickness of .095 or .120. Excellent for building a custom panhard bar for UTVs, cars, trucks & more. Includes LH and RH heim joint, with matching bungs. Available with or without high misalignment spacers.

Be sure to choose tubing wall thickness and misalignment spacer options before ordering!

Yamaha Rhino 686cc Big Bore Kit 2004-2007 (top end cylinder kit)

Bolt on 102mm 686cc Big Bore Kit for all Yamaha Rhino Raptor and Grizzly 660 models. This is a complete bolt on kit with everything you need. Breathe new life into your Yamaha with our high quality, affordable and reliable big bore kit!

50 Caliber Racing rod end fabrication kit. 5/8 x 5/8 chromoly heim joints with nylon/teflon liner, jam nuts, and chromoly steel weld in bungs. Designed specifically for 1.25" OD tubing with wall thickness of .095 or .120. Excellent for building custom sway bar end links for UTVs, cars, trucks & more. Includes two LH and RH heim joints, with matching bungs. Available with or without high misalignment spacers.

Be sure to choose tubing wall thickness and misalignment spacer options before ordering!

Discontinued

16 Tapered Splined Lug Nuts with Chrome Finish and Anodized Aluminum Spike - 10 x 1.25 Thread Pitch

Be sure to select color before ordering!.