List of products by brand 50 Caliber Racing

Replacement 27mm Carburetor for Honda Fourtrax Recon TRX250

Tie Rod End Kit for Suzuki LT250 ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Tie Rod End Kit for Polaris Sportsman ATVs

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Tie Rod End Kit for Yamaha ATVs

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Tie Rod End Kit for Yamaha Raptor YFM660 ATVs

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

50 Caliber Racing CDI module for 660 Yamaha Rhino and Grizzly

Our performance CDI module will give you the most bang for your buck. With increased spark energy you will experience easier starting and better throttle response. Removes the speed limiter and increases max revs by 1000 to 7800 RPM. It also will eliminate the reverse rev limiter. Compatible with both standard gauges and Rhino digital dash. Also compatible with factory exhaust and factory intake. Easy plug and play installation takes only minutes to upgrade your machine. 

Tie Rod End Kit for Honda FL250 Odyssey ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. This kit will service one side. Includes 1 inner and 1 outer end for the tie rod on your Honda.

Tie Rod End Kit for Kawasaki KFV 750 Brute Force ATV

High quality aftermarket tie rod ends from 50 Caliber Racing. Includes 1 inner and 1 outer ends and hardware. This kit is for one side only. If you need to replace both left and right sides, you must order 2 kits.

Vintage Stage 1 88cc Big Bore kit (52mm bore)

- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation
- High compression 52mm piston with rings, pin, & clips (can still run pump gas)
- Head gasket kit includes all gasket needed to install bore kit.

Vintage Stage 2 88cc Big Bore kit

- Fits 1968-1981 honda z50, ct70, atc70, trx70, sl70, xl70
- 20mm Carburetor
- 52mm Piston and cylinder
- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation

50 Caliber Racing Race Head, 88cc Big Bore kit, and 20mm Carburetor

Our Race Head has been updated for even more performance! It now has 25/22mm valves with better porting/flow. We also kept the combustion chamber the same size and changed the angle of the valves slightly. This will really wake up your stock engine and is comparable in power to the much larger Chinese 124cc engines!

Wet Clutch Assembly for Yamaha Rhino and Grizzly 660

Fully assembled replacement wet clutch. Ready to install and get your machine back on the trail.

Fits the following Yamaha models:
- Rhino YXR 660 (2004-2007)
- Grizzly YFM 660 (2002-2008)

440cc Big Bore Kit with 89mm Piston for Honda XR400R / TRX400EX 1996- 2016

Bolt on 89mm 440cc Big Bore Kit for all Honda TRX400ex and XR400 models. This is a complete kit, with everything you need to rebuild your top end.

50 Caliber Racing 12V Wire Harness Kit with Relay and Switch

Universal 12 Volt wire harness kit complete with 40 amp relay, fuse and On/Off switch. This kit will allow you to safely connect a LED Light Bar, Fog Light, Lighted Whip, Pod Lights, or any other 12 volt accessories to your vehicle.

Illuminated 50 Caliber Racing On/Off Rocker Switch with laser etched design -"Boom Box"

High quality 50 Caliber Racing backlit SPST ON/OFF rocker switch with a custom laser etched design and dual LED illumination are rated for 12 Volts and 20 Amps. These waterproof, durable switches are perfect for your boat, car, truck, sand rail or UTV!

Be sure to select the correct color before ordering!

Illuminated 50 Caliber Racing On/Off Rocker Switch with laser etched design - "Dome Light"

High quality 50 Caliber Racing backlit SPST ON/OFF rocker switch with a custom laser etched design and dual LED illumination are rated for 12 Volts and 20 Amps. These waterproof, durable switches are perfect for your boat, car, truck, sand rail or UTV!

Be sure to select the correct color before ordering!

Illuminated 50 Caliber Racing On/Off Rocker Switch with laser etched design - "420 Leaf"

High quality 50 Caliber Racing backlit SPST ON/OFF rocker switch with a custom laser etched design and dual LED illumination are rated for 12 Volts and 20 Amps. These waterproof, durable switches are perfect for your boat, car, truck, sand rail or UTV!

Be sure to select the correct color before ordering!

 50 Caliber Racing On/Off Rocker Switch with laser etched design - "Nautical Star"

High quality 50 Caliber Racing backlit SPST ON/OFF rocker switch with a custom laser etched design and dual LED illumination are rated for 12 Volts and 20 Amps. These waterproof, durable switches are perfect for your boat, car, truck, sand rail or UTV!

Be sure to select the correct color before ordering!

50 Caliber Racing LED lighted whips are super bright and fully adjustable, with over 300 different strobe effects & light patterns, and 20 different color options. Comes with a remote control or you can use the bluetooth app on your smart phone. Quick connect base and flexible water/sand proof outer casing. Each whip comes with a 50 Cal flag and and swivel clip mounts. Add safety and visibility to your UTV, truck, Jeep, sand rail and more! Available in 4 and 6 foot lengths.

Be sure to choose length when ordering!

Brand new with 1 Year Warranty, 50 Caliber Racing single piston Rear Brake Caliper assembly for your Honda ATV. Includes billet parking brake block off plate which is removeable in order to maintain the use of your existing parking brake. Comes with new Pads plus assembly hardware shown, however the bracket is not included so you're required to use your current caliper mounting brackets with this Caliper.