Active filters
High Volume oil pump for 1992 to current year Honda xr and crf 50. Fits all years of xr and crf, Delivers 3 times the amount of oil over stock pump.
Complete set of Honda 50 pit bike spokes and nipples for one wheel - 50 Caliber Racing
* Be sure to select size before ordering!!
Fits the following Honda Pit Bikes:
- CRF50 - All years
- XR50 - All years
- Z50 - All years
Stage 1 88cc Big Bore kit for 88-99 Z50, 2000-2020 xr and crf 50's
- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation
- High compression 52mm piston with rings, pin, & clips (can still run pump gas)
- Head gasket kit includes all gasket needed to install bore kit.
Premium Grade 20mm Performance Aftermarket Carburetor for Honda 50 Pit Bikes with 88cc Big Bore Engines!
Intake throat diameter: 20mm
Bolt hole spacing: 48mm
Air filter mount diameter: 32mm
Fits:
- Honda 50 XR50 CRF50 XR70 CRF70 (Sized for 88cc - up Big Bore modified engine. Not recommened for stock engines)
50 Caliber Racing Pit Bike 12 inch Rims - 32 Hole
High quality 6061 Aluminum Pit Bike Rims with 32 spoke holes. Select your color to purchase, available in BLACK, GOLD, RED or BLUE Anodized. Fits CRF and XR 50 Pit Bikes, and anything else that requires a 12 inch wheel with 32 spokes.
Honda Rancher TRX350 Top End Cylinder Kit 2000-2006
DISCONTINUED
Complete top end rebuild kit for your Honda Rancher TRX350! Our kits are high quality, complete and ready to build right out of the box. You'll be able to take confidence that you'll have the precision components you need to get your toys running again, the right way.
50 Caliber Racing aluminum skid plate. Protect your motor before its too late. Fits all Honda crf xr 50 and 70s.
Honda xr50, crf50, and xr70.
NOTE**** These skid plates all have blemishes in them. They were not packaged good and all have minor scratches and or dings in them.
Stage 2 88cc Big Bore kit for Honda xr70 and crf70 all years
- 20mm Carburetor kit
- Performance camshaft
- Lightweight aluminum cylinder with steel sleeve
- Cast in mounts on cylinder for aftermarket skid plates
- Oversized cooling fins on cylinder for efficient heat dissipation
- High compression 52mm piston with rings, pin, & clips (you can still run pump gas)
- Head gasket kit
Carbon Fiber 50 Caliber billet twist throttle - Throttle will fit any 7/8" aftermarket bar, the standard size bar in the industry. This throttle will not fit the stock Honda XR50, CRF50, Z50 Handle Bars. We have 5 different colors to choose from.
12 Way Standard LED Circuit Screw Fuse Block
This fuse box is suitable for all kinds of automotive and marine applications, including 6V, 12V & 24V systems (maximum voltage 32V). Each fuse holder is designated a custom label for identification and to make fuse installation as easy as possible.
High Performance 20mm Carburetor and Intake Kit for 50cc/70cc Honda 50/70. This carb should be used on big bore engines, 88cc-125cc.
Brand new with 1 Year Warranty, 50 Caliber Racing single piston Rear Brake Caliper assembly for your Honda ATV. Includes billet parking brake block off plate which is removeable in order to maintain the use of your existing parking brake. Comes with new Pads plus assembly hardware shown, however the bracket is not included so you're required to use your current caliper mounting brackets with this Caliper.
50 Caliber Racing 12V Wire Harness Kit with Relay and Switch
Universal 12 Volt wire harness kit complete with 40 amp relay, fuse and On/Off switch. This kit will allow you to safely connect a LED Light Bar, Fog Light, Lighted Whip, Pod Lights, or any other 12 volt accessories to your vehicle.
6 Way Standard LED Circuit Blade Fuse Box aka Power block
This power block is suitable for all kinds of automotive and marine applications, including 6V, 12V & 24V systems (maximum voltage 32V). Each fuse holder is designated a custom label for identification and to make fuse installation as easy as possible.
